A wired fabric-based element is a detached piece that you want to attach to the main design whislt including the fabric the element has been stitched on. This is in contrast to wired needlelace shapes, which are worked on a fabric pad, then totally removed from it. Here, the fabric is part and parcel of the shape you want to create and so the method is a little different. This tutorial doesn't spend much time on embroidery stitches, but it focuses mainly on the wiring and preparing of the detached element.
First of all, you need to cut and bend your wire to shape. Stumpwork wire bends easily, so you won't need any special tools to do this. Having said that, don't use your normal embroidery scissors to cut the wire - use wire cutters or, as I do, specially toughened goldwork scissors which were made for cutting metallic wires and threads.
Mount a piece of fabric into a small hoop and couch the wire shape in place using a thread that will not show against the colour you choose for your outermost layer. It's also worth working on the nearest colour plain dyed fabric you have to that shade too so that fewer cut ends of fabric show when you get to later stages. I say plain dyed fabric as, if it is only painted or printed, the chances are that the middles of each actual fabric thread may not have taken much (or any) of the colour and may show up white. In this case, I needed white, but often you will want something else.
Fill in with your choice of embroidery stitches, picking colours, threads and textures that are best suited to your design. With some fabrics, you may want to minimise or even totally skip this step as you may want the fabric itself to show up clearly with no stitching, or just with some minor decorations such as leaf or wing veins (for dragonflies, for example) and this style seems to be gaining in popularity, possibly owing to speed!!
Once the shape is essentially full of as much stitching as you need, then you need to stitch the whole element securely together. Some like to do this part first, before filling in and, if that's how you want to work, go ahead! I prefer to do it later.
There are basically two different ways of doing this securing - one is to use overcast stitch as seen above - just bring the needle up very close to the wire outside the shape and bring it back down again just inside, simply wrapping the wire whilst sewing it to the fabric thoroughly. Again, some might want to come up inside the shape and go down outside and you can, of course, do it that way too. I prefer this way around though so that I don't risk splitting and damaging any stitches inside the shape.
The other method is to work around the edge with buttonhole/blanket stitch - which hides any stray thread from the fabric a little better. Whichever stitch you chose, make sure you work individual stitches very closely together and completely cover the wire.
Here's our shape with the embroidery stitches all complete and secured with white overcast stitches.
To cut the shape out, first go around it fairly roughly - just to detach it from the majority of the fabric it was worked on. After that, cut around it quite closely.
At this point, I switch to a very fine, sharp pair of scissors (these are my petit point scissors that I use for removing threads in drawn and cut work) and cut even more closely. When you think you're done, run your fingernail all along the edge of the shape and you'll find a few threads may stick up and you can trim them off quite easily.
If your edging is buttonhole/blanket stitch, you may find it easier to turn the shape over and cut the threads from the back. Often cutting at a perpendicular angle helps to protect the stitches. Cut as close as you can to prevent fabric showing. I've seen some otherwise lovely raised pieces spoiled by insufficient trimming and/or not using coordinating foundation fabric for the wired elements! White edges are not inevitable!
If, despite all cautions, you do snip a thread, all is not lost! Just go over it with a glue stick (like Pritt), rubbing lightly down around the cut edge. There are also products, such as Fray Check, on the market if you want to invest in something specialist for this sort of job. (Thanks for the tip, Marie!)
And that's it, your detached, wired element is ready to be joined to the rest of your piece.
Here are a few other uses for this type of shape:
Sparkling wings worked on organza and with veins put in with Kreinik blending filament
Raised flower petals - this one worked with buttonhole edging
I'm sure you can think of many more.....
Text and images: © Elizabeth Braun 2013